Our spider crane on a house job
The spider crane goes where the crane truck can't: carried to site on the truck, set up on its outriggers, and run by our crew to lift steel into a house build.






Real jobs from our Campbellfield workshop: steel fabrication, machining and repairs. Photos from our own phones, no stock pictures.

The spider crane goes where the crane truck can't: carried to site on the truck, set up on its outriggers, and run by our crew to lift steel into a house build.






A motor and gearbox set up on a conveyor's drive drum in our workshop, then fitted to the conveyor at the concrete plant.




A big steel sheet folded on our press brake, with the crane truck reaching into the workshop to carry its weight while it was bent.



Some of the gear at Bancell Street: our spider crane, the saw line for cutting steel to length, the press brake for folding, and a screw conveyor for a concrete plant, which carries cement up from the silo.




DFV fabricated and installed a bolted steel mezzanine frame inside a warehouse unit: painted universal beams fixed to the tilt-up walls, carrying galvanised joists on bolted cleats.



DFV made galvanised batten screens, fence panels and pedestrian gates in the workshop, then craned a screen into an upper-floor opening and hung the powder-coated fences and gates on site.







DFV welded up a cracked pin boss on a mini excavator dipper arm, plated the worn underside and added three steel wear bars, then painted the arm yellow again.




We cut the worn, cracked grid out of an excavator sieve bucket, rebuilt the side edges and welded in a new curved grid of steel bars.





We stripped the counterweight off a mini excavator, repaired a cracked frame plate, welded in a new counterweight mount and gusset, levelled it and painted it before refitting.





We built a long trailer chassis from blue box section in our workshop, with a tapered drawbar, cross members and side rails, setting it up on stands and lifting it with the overhead crane.



DFV's own crane truck lifted a fabricated steel box frame up to a scaffolded multi-storey house under construction.

DFV supplied and installed the steel beams and posts that replace the back wall of a house, then built a steel roof frame of beams and galvanised purlins over the new extension.




DFV used its own crane truck to lift prefabricated steel wall frames up onto a three-storey townhouse block, and installed the grey steel posts and beams along the building's front.






DFV filled in a floor void beside a feature stair in a commercial building: anchoring brackets into the existing concrete, bolting new steel beams across the opening and laying the steel deck for the new floor.






We fabricated a heavy-plate winch mount with welded gusset supports onto the rear of a tag trailer in our workshop, fitted the winch, then painted the new steelwork.



A worn pivot lug was clamped to the milling machine table and its bore was opened out with a boring head.


We bored out a worn wheel hub on the mill, turned a new steel sleeve on the lathe to suit, then fitted and welded the sleeve into the hub.





We built a steel stair and landing platform with mesh guarding and grating treads in our workshop, painted it black, and stood it up ready for use.



Steel beams and posts fabricated at our Campbellfield workshop to the engineer's drawings, then craned into the brick shell of the house and set on the new slab.







Columns, beams and joists put up inside a warehouse, then sheeted over to make a new floor.




Stringers and checker plate treads welded up in the workshop, then painted and fitted to the mezzanine with handrails.





A steel canopy along a new commercial building, a beam going in on a building site, a galvanised frame on the workshop floor, and long beams on stands in the workshop.




Spear-top gates with perforated mesh infill, made in the workshop and fitted on site.



Made up in the workshop, then run up the outside wall of a house and above the roofline.


Subframe, floor, sides, cladding and paint, all done in our workshop under the gantry crane.






Stripped back in the workshop, cleaned of caked concrete, and the rear suspension painted.




Box section drilled and fitted with a studded bracket in the workshop, then welded in between the subframe rails of a concrete truck and bolted down to the chassis.



An old trailer brought into the workshop, painted, and fitted with a spare wheel, a toolbox and a drum holder.





The arm came off on site, had a steel plate welded over the crack in the workshop, then went back on the machine.





Cut from steel plate in the workshop, painted, and clamped to the edge of a loader bucket.



Plate and framed steel panels made in the workshop and set in place on site.




A steel drum built on a machined shaft, with the shaft welded through the end plate and a bearing block fitted.



48 Bancell Street, Campbellfield: the gantry crane, the machine shop and the crane truck that delivers our steel.







Send the drawings or a photo and David will call you back. For anything urgent, ring.
Call David direct0408 758 491