Photo gallery: our steel fabrication and repair work
146 photos from our Campbellfield workshop and our jobs, newest first. All taken by us, no stock pictures.

Set up outside our workshop
Loaded onto the crane truck
Outriggers down
Lifting a steel frame into a house
Holding a beam in a backyard
Our crew running the lift
The gearbox on its frame
Lowering the motor on
Coupled to the drive drum
Fitted at the plant
Folding the sheet on the press brake
The fold forming along the tooling
The crane truck carrying the sheet
Our spider crane, folded up
The saw line for cutting steel to length
Our press brake
A cement screw conveyor for a concrete plant
Beams up, the next one slung
Bolted cleats carrying the joists
The frame finished
Batten screen panel welded up
Galvanised frame with slats fitted
Fence panels ready for powder coat
Screen craned into the upper opening
Front gate hung between brick piers
Batten fence fixed between walls
Batten gate on self-closing hinges
Cracks around the pin boss
Pivot boss welded up
Three wear bars welded on
Plate and wear bars, before paint
Repaired arm, freshly painted
The worn grid before the rebuild
Cutting out the old grid
The bucket shell stripped back
New notched rib welded to the side
The new grid going in
Every joint in the grid welded
The rebuilt sieve bucket, finished
The cracked frame plate
Counterweight off, excavator in the workshop
Levelling the new mounting post
New mount and gusset welded in
Repair underway on the workshop floor
Repaired and painted, ready to refit
Drawbar rails clamped up for welding
Chassis lifted on the overhead crane
The welded trailer chassis
Lifting a steel box frame into place
Lifting a roof beam into place
Steel beam and posts replacing the back wall
Steel roof frame over the extension
Purlins bolted to welded cleats
Lifting a wall frame onto the townhouses
Frame mid-lift on our crane truck
Crane set up beside the new posts
Our truck beside the installed steel
Steel posts and beams along the facade
A beam going in over the street fence
Steel beams and columns inside
A steel frame on the roof deck
Drilling anchors for the beam brackets
First beam across the void
Beams bolted in under the stair
Laying the steel deck
The new floor from below
Looking up the atrium
Winch mount welded, before paint
Gussets welded under the top plate
Mount painted, sockets masked
Gussets fitted before the top plate
The pivot lug and its bore
Boring the lug out on the mill
The hub bored out, ready for a sleeve
Boring the hub on the mill
Boring the new sleeve on the lathe
The turned sleeve in the chuck
New sleeve fitted and welded in
The finished stair and platform
Built in our workshop
Painted and standing on the floor
Grating treads and handrails
The crane set up to lift the steel in
Beams rigged and ready to lift
Beams across the brick walls
Posts set on the slab
The beam and post frame in place
Ready for the floor above
Checking the frame from on top
Columns, beams and joists up
Galvanised joists between the beams
Sheeting the new floor
Finished, with an office built on top
Welded up in the workshop
Painted and fitted to the mezzanine
Handrails on
In use
The floor and stair from below
A steel canopy along a new building
A beam hung across a building under construction
A galvanised frame, with our crane truck
Beams on stands in the workshop
Fitting the hinges in the workshop
Fitted in a side passage
Between the new fence and the house
Made up in the workshop
Fitted to the house
New subframe on the chassis
Floor frame on, under the gantry crane
The sides, built on the workshop floor
Crate frame fitted to the truck
Clad in steel sheet
Painted, with the rear gate going on
Caked in concrete underneath
Stripped back to the chassis
Cleaned, with the torque rods painted
Suspension and air lines done
Box section drilled on the bench
Welded in between the subframe rails
The end bracket, bolted to the chassis
Stood on end in the workshop
Painted
Back on its wheels
Fitted out with a toolbox and drum holder
Coupling, chains, jockey wheel and spare
Lifting the arm off on site
The crack, marked up
A plate welded over it
The repair finished
Repainted and back on the machine
Cut from plate
Painted
Clamped to the bucket
A plate panel on the overhead crane
Braced on the back
A framed panel, painted
Set in place on site
Shaft welded through the end plate
On the trestles
Bearing block fitted
The 6.3 tonne gantry crane
The crane truck loaded in the workshop
Beams on the workshop floor
A welded frame on the chains
The machine shop
The workshop from the yard

Got a job like these?
Send the drawings or a photo and David will call you back. For anything urgent, ring.
Call David direct0408 758 491Workshop48 Bancell Street
Campbellfield VIC 3061
Get directions
Campbellfield VIC 3061
Get directions
Workshop phone(03) 9357 2890
HoursMon to Fri, 7 am to 3:30 pm
Where we workCampbellfield and Melbourne's northern suburbs, and out to Bacchus Marsh and Dandenong for the right job.